RCScrapyard ► Radio Controlled (RC) Models, Parts and Spares ► Traxxas Bullet (TRX-10). For Sale in The USA.

Tamiya Buggys RCScrapyard: New, used, second hand radio controlled models, parts and spares.
Established 1999
Tamiya Monster Buggy
Site Search
Complete RC Model Listings    USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap    From Around The WORLD

1/10 Scale Electric Buggy:

Traxxas Bullet (TRX-10)


USAUS UKUK AUSAU CANCA ESES IEIE DEDE FRFR ITIT NLNL ATAT CHCH

How To Set-up, Hints and Tips for the Traxxas Bullet:

  To obtain the most you possibly can from your Traxxas Bullet, You need to tweak and adjust all you can to give your car improved handling, stability and grip to ease around the curves and keep you on the track. One little setting change can transform your car into a world beater. Just follow our chart to the to the most favourable Set-up to suit your particular needs on any track.
  Learn what to look for when you search for the right Electric Motor for your Bullet, and achieve the best Gearing, for the best performance and put you on the winners rostrum.
  See how the highest level racers optimise and halve the friction of their Bearings with some easy to implement tips. Discover what you can do to avert Radio interference, and the optimum conditions to Charge your Batteries To help keep them in good condition and give you excellent performance.


★ Traxxas Bullet (TRX-10) ★
Traxxas Bullet - TRX-10 - 1:10 Electric RC Buggy






★ Radio Controlled Model Accessories: ★
Electric Motors
Motors by Can Size
Brushless Motors
Motors by Turns
Electronic Speed Controllers
ESC
Battery Packs
Batteries and Chargers
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Radio Transmitters etc
Radio Equipment















USA

Traxxas Bullet: For Sale in the USA

Logo

★ Traxxas Bullet: ★


USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap


Buying a Used Traxxas Bullet Buggy.


   Buying a used Traxxas Bullet Electric Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase they can often be downloaded from the Traxxas website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

   When you receive your used Traxxas Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for anything broken that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. Next, for those Traxxas models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Traxxas Bullet is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Bullet model, fit an under guard to stop dirt and gravel entering the chassis.

   Examine the drive shafts for wear and replaced as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Bullet Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

   The Bullet steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Traxxas Bullet is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

   If your used Traxxas Buggy comes with plastic and sintered brass ring type bearings, check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Bullet model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.


^ TOP ^


Click Here


Not Here?
Maybe Tomorrow.
♥ Add This Page to your Favorites (Ctrl+D) ♥

★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Bearings and Bearing Sets
Bearings
Body Shells
Body Shells
Radio Transmitters etc
Radio Equipment
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Electronic Speed Controllers
ESC
Battery Packs
Batteries + Chargers
Electric Motors
Electric Motors






Hints and Tips

On Road Drifting

   Drifting is the greatest fun you can have on four wheels, but it isn't as easy as it might look. There are lots of different methods and ideas on how it should be done and it takes lots of practice to get it right.

   On the street or in the parking lot, drifting is fine, but until you have had hours and hours of practice to master the technique, don't try it on your local race track. If you don't have the total control of your car, you will not make many friends amongst your immediate competitors.

   Controlled Drifting is a beautiful thing when done correctly, and in this article I will endeavour to give you a few pointers on where to start. After that, your own personal style will soon blossom.

   As I mentioned before, there are a number of different ideas about drifting, but basically this is what you do.

   Consider a 180 degree turn. Enter the corner at speed, start to turn a little sooner than you might, then just before the apex, touch the breaks for a split second, enough to break the rear of the car free as you enter to turn. When the car begins to slide sideways, steer into the slide, increase the throttle, just enough to balance the car as it drifts around the turn. Coming out of the corner, steer the car straight and apply full throttle.

   Often referred to as a power slide, drifting is much more fun than the basic "Rounding" style, described in a previous article, but also takes more skill, not just in its execution, but in car set-up.

   A little "body-roll" is the thing to aim for when setting up a drifting car, but be careful. With too much body-roll, the car will be difficult to control and tumble sideways off the track. Too little and the weight transfer to the leading wheels will not be enough to induce the slide. A lot of trial and error, with tuning springs, damper oil, damper pistons, stabilisers, tires and inserts is required to get your car as you want it, but believe me, if you can get it right, it will be well worth all your effort.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Soldering Battery Packs

   Nicad and Nimh batteries sometimes come as six separate matched 1.2 volt cells. These of course have to be soldered to each other in series to produce either a side by side stick pack, or a two times three cell saddle pack.

   Special copper, or silver plated straps must be used to make up these packs, and each strap must be prepared before attempting to solder it to the battery cell, by placing a blob of solder at each end of all the straps needed.

   A jig to hold the cells vertical and side by side is advisable. Using electrical solder, with a flux core (flux aids the flow and adhesion of the solder) heat your soldering iron to as hot as it will go. Then with the stick of solder touching on the end of the cell, touch it with the iron. What you want it to spread evenly on the central part of the pole of the cell. Count to 3 seconds. If it doesn't melt the solder in that time, your iron is not hot enough. Battery cells are notoriously very fragile, and susceptible to the very high temperatures soldering requires. Anything longer than four or five seconds direct contact with the iron can cause damage to the crystal structure in the cell, so be wary.

   When you have solder on each end of each cell, line them up in the jig, positive to negative and dab a spot of flux on the soldered cells, then position your straps, with the solder coated side faced down, touching the solder on the end of the cell. Now place your hot iron on the strap. Heat will transfer through the strap and melt the solder on the two faces. Again, count to 3 and you should feel the strap drop slightly as the solder fuses with the solder on the cell. Repeat this for each cell on both sides to produce your desired configuration. Finally solder your two wires, previously prepared with connectors, to the pack. Do not solder wires with bare ends to your pack. If these wires were to touch and short out, you could effectively kill your expensive battery pack I use Red for positive and Black for negative, but so long as you know which is which electrical equipment does not like the battery to be connected the wrong way.

For More Setup Information check out my Hints and Tips page.








Trend Times Toy Store


On/Off Road
RC Models:

Other RC Models:

Radio Equipment:

Accessories:
Buggys
Formula One
Monster Trucks
Rock Crawlers
Touring/WRC/Drift Cars
Trucks/Truggys


Airplanes
Boats/Ships
Helicopters
Motorcycles
Submarines
Tanks


Crystal Sets
Receivers
Servos
Transmitters


Batteries
Battery Chargers
Bearings
Body Shells
Dampers (Shocks)
Electric Motors


ESC
Nitro Engines
Pinion Gears
Spur Gears
Tires
Wheels