Radio Controlled Models
Share RCScrapyard on Facebook
RCScrapyard Radio Controlled Models
Flags
RCScrapyard.net contains Google AdSense Ads and Amazon Affiliate links, from which we may earn commission. See our Disclosure page for more information.
bar

1/10 Scale Electric Rally/Touring Car:

Team Magic E4-RS II - TM 507001 - Radio Controlled Model



History and Info for the Team Magic E4-RS II:

  Introduced by Team Magic circa 2010, the 4WD E4RS II Black Magic Rubber Spec Touring Car Chassis - # TM 507001 - was classed as a top spec competition bare chassis.

  The E4RS2 is belt driven, on a double deck woven graphite chassis, with front and rear gear type differentials, coil spring over oil filled dampers, steel universal joint drive-shafts and a full set of ball bearings.

Team Magic E4RS II

▼ Scroll Down for More Images ▼


  To race the Team Magic E4-RS II, it calls for fine tuning to attain better steering response and improve grip when cornering so you don't slide off the side of the track. Minute changes can make huge advancements. Our easy to understand list will show you how and lead you to the optimum Set-up to put you in front of the rest on the track.








Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors















Flags
★ Team Magic E4-RS II Black Magic ★
Team Magic E4-RS II Black Magic
★ Team Magic E4-RS II Chassis ★
Team Magic E4-RS II Chassis
★ Team Magic E4-RS II Chassis ★
Team Magic E4-RS II Chassis
★ Team Magic E4-RS II Chassis ★
Team Magic E4-RS II Chassis

Buying a Used Team Magic E4-RS II
Touring Car (and What to look for)


   There are essentially three reasons you might want to buy a used Team Magic E4-RS II Electric Touring Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

   Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Team Magic website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
   When you receive your used Team Magic Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Team Magic models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

   If the body shell of your Team Magic E4-RS II is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your E4-RS II model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your E4-RS II Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

   Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

Pinions and Spur Gears

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
   The E4-RS II steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

   If body roll on your Team Magic E4-RS II is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

Ball Bearings
   If your used Team Magic Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your E4-RS II model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide

^ TOP ^












Manufacturers and Brands Catalogued, Listed and Reviewed by RC-Scrapyard.

   At present, the RC Model Manufacturers, Brands and Distributors covered by us are: ABC Hobby, Academy, Acme Racing, Agama Racing, Amewi, Ansmann Racing, ARRMA, Team Associated, Atomic RC, Axial, AYK, Bolink, BSD Racing, Capricorn, Carisma, Carson, Caster Racing, Cen, Corally, Custom Works, Durango, Duratrax, ECX - Electrix, Exceed RC, FG Modellsport, FS-Racing, FTX, Fujimi, Gmade, GS-Racing, Harm, HBX, Helion, Heng Long, Himoto Racing, Hirobo, Hitari, Hobao, Hong-Nor, Hot Bodies, HPI, HSP, Intech, Integy, Jamara, JQ Products, Kawada, Kyosho, Losi, LRP, Maisto, Mardave, Marui, Maverick, MCD Racing, Megatech, Mugen, New Bright, Nichimo, Nikko, Nkok, Ofna, Pro-Pulse, Protech, PTI, RC4WD, Redcat Racing, RJ-Speed, Robitronic, Schumacher, Seben, Serpent, Smartech, Sportwerks, Step-Up, Tamiya, Team-C Racing, Team Magic, Thunder Tiger, Tomy, Top Racing, Traxxas, Trinity, Tyco, Vaterra RC, Venom, VRX Racing, WLToys, X-Factory, Xmods, Xpress, Xray, XTM, Yankee RC, Yokomo, ZD Racing and Zipzaps.

   This is an ongoing project, with new and "lost in time" RC Models and Brands being added as they are found and although most of those listed above have been covered in relative detail, some are still being researched and will be completed in the near future.



















Hints, Tips and Information

Painting a Lexan Body Shell.

   Most RC Model kits come with an unpainted, clear Lexan plastic Body Shell you yourself must prepare and paint. This type of Body Shell is painted on the inside, and special spray or brush on Polycarbonate Paints MUST be used.

   The beauty of this is you can go wild and show off your artistic ability, or simply choose your favourite colour, and add some choice decals later.

   This article is for those who have never done this kind of thing before, and need some basic guidance.


   Firstly, cut off the waste from the body shell with sharp scissors. If required finish off the rounded wheel arches with smooth sandpaper wrapped around a drinks can.

   Any holes for body posts must also be drilled before painting. Place the clear body shell over the model and adjust the posts so the shell is in the desired position. Where the posts touch the shell make a small dot with a marker pen.
Next, pierce small holes in the shell where the dots are from the inside. Place the shell on an old piece of wood and drill the post holes, again, from the inside.

Read the Complete Article  ▶ ▶






Hints, Tips and Information

Driving On Road

   The basic driving style most commonly used for all forms of on road, tarmac and carpet racing, involves using the full width of the road available, and cutting each apex as tight as possible, whilst keeping complete control of the car on the track. The style, often referred to as "Rounding" looks quite simple to those watching, but to get it right needs good hand eye coordination and lots of practice.

   Consider a 180 degree turn. As you enter the corner, start with the car positioned close to the outside of the track, then as you approach the corner brake hard, but not too hard, just enough to slow the car so you maintain control and smoothly guide the car across the point of the apex, gently sweeping round until you are approximately 75% around the corner. At this point, gradually increase the throttle out of the corner, under full control and guiding the car to the opposite outside line. By the time the car is pointing straight on the track, you should be at almost full throttle, before you brake hard again for the next corner.

   Developing this driving style comes in stages.

Read the Complete Article  ▶ ▶







RC Models:
Radio
& Motors:
Other
Accessories: