RCScrapyard ► Radio Controlled (RC) Models, Parts and Spares ► Kyosho Inferno GT2. For Sale in The USA.

Tamiya Buggys RCScrapyard: New, used, second hand radio controlled models, parts and spares.
Established 1999
Tamiya Monster Buggy
Site Search
Complete RC Model Listings    USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap    From Around The WORLD

1/8 Scale Nitro Rally/Touring Car:

Kyosho Inferno GT2


USAUS UKUK AUSAU CANCA ESES IEIE DEDE FRFR ITIT NLNL ATAT CHCH

How To Set-up, Hints and Tips for the Kyosho Inferno GT2:

  To get the best from the Kyosho Inferno GT2, it must be fine tuned to improve handling, provide responsive steering and give you the grip to cruise around corners at high speed, without slipping off the track. Small adjustments can make a Big difference and our step by step procedure, will guide you to the best Set-up for your individual driving style.
  Our simple guide explains run in and what to look for as you tune the Nitro Engine for your Inferno GT2.
  Using plain language, our guide will show you how to avoid Radio interference, and Servo Twitch, by positioning your radio receiver and implementing the latest innovations. Find out how to reduce friction and improve the performance of your Kyosho Inferno GT2 Bearings with a few common sense hints and tips.


★ Kyosho Inferno GT2 ★
Kyosho Inferno-GT2






★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Glow Plugs
Glow Plugs
Starters
Starters
Nitro Fuel
Nitro Fuel
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Radio Transmitters etc
Radio Equipment















USA

Kyosho Inferno GT2: For Sale in the USA

Logo

★ Kyosho Inferno GT2: ★


USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap


Buying a Used Kyosho Inferno GT2
Touring Car.


   Buying a used Kyosho Inferno GT2 Nitro Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase they can often be downloaded from the Kyosho website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

   When you receive your used Kyosho Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for anything broken that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. Next, for those Kyosho models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Kyosho Inferno GT2 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Inferno GT2 model, fit an under guard to stop dirt and gravel entering the chassis.

   Examine the drive shafts for wear and replaced as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Inferno GT2 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

   The Inferno GT2 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Kyosho Inferno GT2 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

   If your used Kyosho Touring Car comes with plastic and sintered brass ring type bearings, check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Inferno GT2 model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.


^ TOP ^


Click Here


Not Here?
Maybe Tomorrow.
♥ Add This Page to your Favorites (Ctrl+D) ♥

★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Bearings and Bearing Sets
Bearings
Body Shells
Body Shells
Radio Transmitters etc
Radio Equipment
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Electronic Speed Controllers
ESC
Battery Packs
Batteries + Chargers
Electric Motors
Electric Motors






Hints and Tips

Shock Mount Settings

   The combinations of Shock settings available on the majority of on and off road cars are far too many for this article to cover, so I will endeavour to explain some of the basics, that should give you some idea what these changes might achieve. Some of the settings suggested may not be available on all RC model cars.

   If you look at the lower wishbones of you model, you may see a number of holes alongside where the ball studs for the dampers are positioned. If you were to remove those studs on the rear wishbone and reposition them in the hole further out from the center of the car, the first thing you will notice is the ride height has dropped, this can be corrected by adding C spacers above the springs. The second thing you will notice is the shocks are more sluggish, this can be compensated by using thinner oil. If this adjustment is made on an off-road car, it can be advantageous for landing after big jumps, providing improved stability due to the increased hydraulic pack in the shocks (as described in my previous article). This setting can also improve the way cars handle small bumps and dips in the track, due to the softer static damping.

   Changing the mounting hole positions used by the dampers, on the wishbone or on the shock tower, will always change the angle the dampers lay. This angle is what changes the characteristics of the shocks in that they will react to different track types and conditions. The above example is just food for thought, for those looking to improve their cars handling in relation to any other settings, such as caster, camber, toe-in etc, they may have previously made on their car. The only way to really get to grips with this subject is through trial and error.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Decals

   After spending lots of time and effort to paint your bodyshell, you come to the point where you make it look good by putting on all those flashy decals, but before you rush in with the scissors and start cutting, there are a few things you should do first.

   Good preparation is key to a perfect job, so before you do anything with your decals, you must first of all wash your hands, and then make sure the bodyshell is clean and no oil or grime from your previously grubby fingers remains on the Polycarbonate Lexan surface. Methylated spirits is the thing to use, or failing that, use one of those wipes you use for your computer monitor screen. As the body shell dries, you can carefully cut out the decals from the sheet. Do the big ones first and leave the smallest ones for last.

   Now you can prepare to the decals for positioning. Carefully remove the backing paper from the decal with your thumb nail, and then put it back on again, but slightly out of line. Place the decal in the position you want it on the bodyshell and when you are satisfied, press down the sticky corner onto the bodyshell and peel off the backing paper, following it along with your fingers to avoid any bubbles. Repeat the process until all your decals are in place.

   Any bubbles or misfitting areas can be corrected by using a sharp modelling knife to carefully pierce the bubbles, or score the poorly fitting area and complete the process with your finger nail.

   Some misalignments can often be fixed using a hair dryer on the offending decal to soften the glue enough to allow you to reposition it, but be careful; Lexan can react like heat-shrink and may wrinkle if you use too much heat.

For More Setup Information check out my Hints and Tips page.








Trend Times Toy Store


On/Off Road
RC Models:

Other RC Models:

Radio Equipment:

Accessories:
Buggys
Formula One
Monster Trucks
Rock Crawlers
Touring/WRC/Drift Cars
Trucks/Truggys


Airplanes
Boats/Ships
Helicopters
Motorcycles
Submarines
Tanks


Crystal Sets
Receivers
Servos
Transmitters


Batteries
Battery Chargers
Bearings
Body Shells
Dampers (Shocks)
Electric Motors


ESC
Nitro Engines
Pinion Gears
Spur Gears
Tires
Wheels