RCScrapyard ► Radio Controlled (RC) Models, Parts and Spares ► Duratrax Vendetta TC Touring Car. For Sale in The USA.

Tamiya Buggys RCScrapyard: New, used, second hand radio controlled models, parts and spares.
Established 1999
Tamiya Monster Buggy
Site Search
Complete RC Model Listings    USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap    From Around The WORLD

1/18 Scale Electric Rally/Touring Car:

Duratrax Vendetta TC


USAUS UKUK AUSAU CANCA ESES IEIE DEDE FRFR ITIT NLNL ATAT CHCH

How To Set-up, Hints and Tips for the Duratrax Vendetta TC:

  If you are looking to win races with your Duratrax Vendetta TC, It calls for fine tuning to attain better steering response and improve grip when cornering so you don't slide off the side of the track. Minute changes can make huge advancements. Our easy to understand list will show you how, and lead you to the optimum Set-up to put you in front of the rest on the track.
  We give you all the basic information you need to guide you to the best Electric Motor for your Vendetta TC, and achieve the best Gearing, to get you in front on the track and keep you there.
  Find out how the worlds top professional RC racers get improved efficiency from their Bearings employing a number of sensible ideas. Find the way to avoid Radio interference, and basic instruction on how to Charge your Batteries So they will last longer and provide improved power.


★ Duratrax Vendetta TC ★
Duratrax Vendetta-TC






★ Radio Controlled Model Accessories: ★
Brushless Motors
Motors by Turns
Electronic Speed Controllers
ESC
Battery Packs
Batteries and Chargers
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Radio Transmitters etc
Radio Equipment















USA

Duratrax Vendetta TC: For Sale in the USA

Logo

★ Duratrax Vendetta TC: ★


USA - Sitemap UK - Sitemap AU - Sitemap CA - Sitemap ES - Mapa del sitio IE - Sitemap DE - Sitemap FR - Plan du Site IT - Mappa del sito NL - Sitemap AT - Sitemap CH - Sitemap


Buying a Used Duratrax Vendetta TC
Touring Car.


   Buying a used Duratrax Vendetta TC Electric Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase they can often be downloaded from the Duratrax website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

   When you receive your used Duratrax Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for anything broken that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. Next, for those Duratrax models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Duratrax Vendetta TC is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Vendetta TC model, fit an under guard to stop dirt and gravel entering the chassis.

   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Vendetta TC Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the road, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

   The Vendetta TC steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Duratrax Vendetta TC is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

   If your used Duratrax Touring Car comes with plastic and sintered brass ring type bearings, check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Vendetta TC model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.


^ TOP ^


    ★ RC Information and Advice ★    





Click Here


Not Here?
Maybe Tomorrow.
♥ Add This Page to your Favorites (Ctrl+D) ♥

★ Radio Controlled Model Accessories: ★
Gas/Nitro Engines
Nitro Engines
Bearings and Bearing Sets
Bearings
Body Shells
Body Shells
Radio Transmitters etc
Radio Equipment
Tires - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Tires
Wheels/Rims - Touring, Buggy, Truck, Monster Truck, Rock Crawler
Wheels
Electronic Speed Controllers
ESC
Battery Packs
Batteries + Chargers
Electric Motors
Electric Motors






Hints and Tips

Radio Gear

How to avoid Interference.


1/  The first consideration when installing your Receiver into your Electrically Powered Model is to make sure it is well away from the Negative Battery terminal, and the Motor. The Magnetic field can cause stuttering type interference at times of high current draw (i.e., Fast Acceleration)

2/  Make sure the Ariel tube is long enough for the Ariel wire. The tip of this wire is highly sensitive and should be as high, and as far away from the Motor as possible (yup, its that magnetic field prob again)

3/  If all else fails, a simple tip that often works for all RC Model enthusiasts is to wrap the receiver in Aluminium Foil, to shield against any magnetic and external radio interference.

4/  As a last resort, to protect against servo twitch, try ferrite beads. (available at Radio Shack or Maplins) These are threaded over the red, white (or yellow) and black wires of each servo.

5/  If you are using a FET Servo, the installation of a choke (a small electrical component) in the positive feed wire will smooth out any current spikes and reduce the possibility of "servo twitch".

6/  Another thing you might try is a "glitch buster" or "stutter stopper". Basically, this is a capacitor that simply plugs into your Radio Receiver and attempts to keep a level voltage supply to the Radio system.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Slipper Clutch and Hydra-Drive

   More often installed on off road RC Models, the Slipper Clutch has been around since the late 1990s. Basically the idea is to prevent wheel spin and increase traction under acceleration, to improve the cars stability from a standing start, when landing from jumps or on corner exits. It also protects the spur gear and drivetrain, to some degree, when using a high torque motor.

   The design is quite simple, employing two independent metal plates, one generally fixed to the spur gear and the other to the drive mechanism, clamping onto a fibre or rubber ring or pad. Adjustment is commonly achieved by slackening or tightening a spring loaded nut on the end of the spur gear mount.

   Setting up the slipper clutch can take some time and is a matter of individual preference, but normally the way to do this is from a standing start, jamming on the throttle and simply getting the feel of the car for that particular surface, being grass, gravel or dust. Personally I adjust it to give me around a metre and a half slip, before it achieves full drive. Wear on the slipper clutch is natural, and often has to be readjusted after each race.

   The Hydra-Drive, or Fluid Coupling design has actually been around since the 1950s, but only came to RC a couple of years after the introduction of the slipper clutch. In principle, the Hydra-Drive is supposed to give similar results to the slipper clutch but need less continuous adjustment. In practice, for me anyway, it was not easy to live with.

   Hydra-Drives employ two independent impellers, immersed in silicone oil and enclosed in a sealed housing. Again, like the slipper clutch, one impeller is fixed to the spur gear, the other the drive. As power is applied, the spur gear will spin its impeller, until through the oil, drive is picked up by the drive impellor. The only real way to adjust the drive was to change the oil viscosity, or in some, the gap between the impellers could be adjusted by shims. All this took time and as far as I am aware, the Hydra-Drive is no longer used in RC.

For More Setup Information check out my Hints and Tips page.








Trend Times Toy Store


On/Off Road
RC Models:

Other RC Models:

Radio Equipment:

Accessories:
Buggys

Formula One

Monster Trucks

Rock Crawlers

Touring/WRC/Drift Cars

Trucks/Truggys



Airplanes

Boats/Ships

Helicopters

Motorcycles

Submarines

Tanks



Crystal Sets

Receivers

Servos

Transmitters



Batteries

Battery Chargers

Bearings

Body Shells

Dampers (Shocks)

Electric Motors



ESC

Nitro Engines

Pinion Gears

Spur Gears

Tires

Wheels