RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Duratrax Street Force GP2.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Nitro Rally/Touring Car:

Duratrax Street Force GP2 - DTXC0052 / DTXD52**


Navigation: Sitemap  >  Manufacturers  >  Duratrax

All Manufacturers: Model Types  >  On Road  >  1/10 Nitro On Road

History, Info and How To Set-up Tips, for the Street Force GP2:


  Introduced by Duratrax in 2004, the 4WD Street Force GP2 Touring Car, was available Pre-Built - DTXC0052 - without a radio system, or RTR - DTXD52** - with a DTX 18 engine, and AM radio system.

  The model was belt driven, on an alloy plate chassis, with ball differentials, coil spring over oil filled dampers, rear dogbones, with CV universal joint drive-shafts, 2-speed transmission, and a full set of ball bearings.

Duratrax Street-Force-GP2

  To race the Duratrax Street Force GP2, it has to have the best settings for your driving style, and provide you with excellent handling and stability. The smallest changes can make a huge difference in the way your car performs on the track, and our comprehensive instructions will help you to find the best Set-up to get you where you want to be.

  If you are having any problems, our guide will show you what to look for and how to fine tune the Nitro Engine for your Street Force GP2.

  With some basic, sensible tips, you will discover just how easy it is to avert Radio interference, and Servo trouble, by moving your receiver or adjusting the position or height of your antenna. See how you can halve the friction and maintain your Duratrax Street Force GP2 Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors


















Flags

★ Duratrax Street Force GP2 ★
Duratrax Street Force GP2

★ Duratrax Street Force GP2 ★
Duratrax Street Force GP2

★ Duratrax Street Force GP2 Chassis ★
Duratrax Street Force GP2 Chassis

★ Duratrax Street Force GP2 Chassis ★
Duratrax Street Force GP2 Chassis


Buying a Used Duratrax Street Force GP2
Touring Car.


   Buying a used Duratrax Street Force GP2 Nitro Touring Car, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the road.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Duratrax website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover can easily be fixed.

Dampers
   When you receive your used Duratrax Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for anything broken that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. Next, for those Duratrax models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Duratrax Street Force GP2 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Street Force GP2 model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Street Force GP2 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Touring Car racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Street Force GP2 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Duratrax Street Force GP2 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Duratrax Touring Car comes with plastic and sintered brass ring type bearings, check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Street Force GP2 model and good racing.


For More on how to Setup your Touring Car, check out my Hints and Tips page.


^ TOP ^






























Hints and Tips

Decals

   After spending lots of time and effort to paint your bodyshell, you come to the point where you make it look good by putting on all those flashy decals, but before you rush in with the scissors and start cutting, there are a few things you should do first.

   Good preparation is key to a perfect job, so before you do anything with your decals, you must first of all wash your hands, and then make sure the bodyshell is clean and no oil or grime from your previously grubby fingers remains on the Polycarbonate Lexan surface. Methylated spirits is the thing to use, or failing that, use one of those wipes you use for your computer monitor screen. As the body shell dries, you can carefully cut out the decals from the sheet. Do the big ones first and leave the smallest ones for last.

   Now you can prepare to the decals for positioning. Carefully remove the backing paper from the decal with your thumb nail, and then put it back on again, but slightly out of line. Place the decal in the position you want it on the bodyshell and when you are satisfied, press down the sticky corner onto the bodyshell and peel off the backing paper, following it along with your fingers to avoid any bubbles. Repeat the process until all your decals are in place.

   Any bubbles or misfitting areas can be corrected by using a sharp modelling knife to carefully pierce the bubbles, or score the poorly fitting area and complete the process with your finger nail.

   Some misalignments can often be fixed using a hair dryer on the offending decal to soften the glue enough to allow you to reposition it, but be careful; Lexan can react like heat-shrink and may wrinkle if you use too much heat.

For More Setup Information check out my Hints and Tips page.







Hints and Tips

Anti Squat

   Described as the angle at which the suspension arms pivot in relation to the chassis, Anti Squat effects traction under acceleration.

   Considered to be at its most effective from a standing start, the handling and stability of the majority of modern day On Road and an increasing number of Off Road models, can be improved with a certain amount of anti squat, normally no more than around 3 degrees.

   Basically, more anti squat gives you more traction, but after a certain point, that advantage is lost and the car will become unstable when turning into high speed corners. For Off Road models anti squat can also improve how the car handles on bumpy tracks.

   Less anti squat allows the car to drop at the rear under hard acceleration, providing less traction, but more stable when cornering. If no anti squat is present, with the lower suspension pivot shaft being parallel to the chassis, steering will be sharp and can induce some over-steer.

   Most manufacturers have some anti squat on their car kits provided as standard and hop-up parts are generally available to change the anti squat angle, but more often, on a wide range of models, all that is needed is a washer or two under one side of the suspension pivot block. However, if the block is held in position using self tapping screws, it may be prudent to change them for slightly longer ones.

   If you are thinking of trying a different setting on your car, not just for anti squat, always remember to only make one change at a time. Too many changes to your set-up made at one time, can make it difficult, if not impossible, to determine which change you made gave you the result you desired.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: