RCScrapyard ► Iconic Vintage Radio Controlled (RC) Model Car Archive ► Duratrax Nitro Evader BX Buggy.
RCScrapyard Radio Controlled Models
Flags

1/10 Scale Nitro Buggy:

Duratrax Nitro Evader BX - DTXC0067 / DTXD67**


Navigation: Sitemap  >  Manufacturers  >  Duratrax

All Manufacturers: Model Types  >  Buggys  >  1/10 Nitro Buggys

History, Info and How To Set-up Tips, for the Nitro Evader BX:


  Introduced by Duratrax in 2003, the 2WD Nitro Evader BX GP Buggy, was available Pre-Built - DTXC0067 - without a radio system, or RTR - DTXD67** - with a Duratrax 18 engine, and radio system.

  The model was based on an alloy plate chassis, with a ball differential, coil spring over oil filled dampers, CV universal joint drive-shafts, slipper clutch, and a full set of ball bearings.

Duratrax Nitro-Evader-BX

  To race the Duratrax Nitro Evader BX, it has to have the best settings for your driving style, and provide you with excellent handling and stability. The smallest changes can make a huge difference in the way your car performs on the track, and our comprehensive instructions will help you to find the best Set-up to get you where you want to be.

  If you are having any problems, our guide will show you what to look for and how to fine tune the Nitro Engine for your Nitro Evader BX.

  With some basic, sensible tips, you will discover just how easy it is to avert Radio interference, and Servo trouble, by moving your receiver or adjusting the position or height of your antenna. See how you can halve the friction and maintain your Duratrax Nitro Evader BX Bearings with a few common sense hints and tips.









Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors


















Flags

★ Duratrax Nitro Evader BX ★
Duratrax Nitro Evader BX

★ Duratrax Nitro Evader BX ★
Duratrax Nitro Evader BX

★ Duratrax Nitro Evader BX Chassis ★
Duratrax Nitro Evader BX Chassis


Buying a Used Duratrax Nitro Evader BX Buggy.


   Buying a used Duratrax Nitro Evader BX Nitro Buggy, or any used RC Model, has a number of advantages. It is generally cheaper than new, ready built and may come with a variety of expensive hop-ups already installed. Cheap, pre-loved bargains are always becoming available. However, depending on the age of your purchase, it may need a little tender loving care before you can take it out on the back yard.

   The one thing you will always need is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Duratrax website, or purchased separately on eBay. With an instruction manual, any problems with your model Buggy you may discover can easily be fixed.

Dampers
   When you receive your used Duratrax Buggy, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for anything broken that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten. Next, for those Duratrax models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

   If the body shell of your Duratrax Nitro Evader BX is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Nitro Evader BX model, fit an under guard to stop dirt and gravel entering the chassis.

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Nitro Evader BX Buggy model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

   The gearbox of your used Buggy should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Buggy at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Spur Gears
   Gears are a weakness on all Buggy RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Nitro Engine in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Nitro Engine mount and remember to check them for security after every two or three runs.

   Ball joints always cause problems. For top level Nitro Buggy racing, the plastic ball connectors should be checked and if deemed necessary changed after every meeting. A simple thing like a loose fitting connector popping off could easily end your race, so better safe than sorry.

Servo Gears
   The Nitro Evader BX steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

   If body roll on your Duratrax Nitro Evader BX is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Ball Bearings
   If your used Duratrax Buggy comes with plastic and sintered brass ring type bearings, check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Nitro Evader BX model and good racing.


For More on how to Setup your Buggy, check out my Hints and Tips page.


^ TOP ^






























Hints and Tips

Tires for RC Models

Sponge (Foam) Tires:

   Sponge Tires can be purchased either pre mounted, glued and trued on the rims, or separately. Fitting the Tires onto the rims can be messy, so here are a few tips to make it a bit easier.
   If you are fitting new Tires on old rims, make sure the old sponge Tire is completely removed. To do this, I recommend using a wood lathe and apiece of wood, at least 300mm long, and more than the width of your wheels, with medium grit emery paper stuck to it ... sand paper will also work, but emery is harder wearing ... This will also be used for truing a wheel. (Described later)

How to Mount and Glue Sponge Tires onto Wheels/Rims.

1/   Mount the Tires on the rims. Make sure they are reasonably tight on the rims, too loose and you might have problems.

2/   I find this to be easier if either in the lathe, or on the car itself. (but be careful with that glue)
  Using your thumb and forefinger, lift up the Tire off the rim, then using a small spatula or a thin piece of rigid wood or plastic dipped in glue (I recommend Evo-Stik, Impact Adhesive) slip it in the gap, making sure both the Tire and the rim are smeared. Then lower the Tire back onto the rim and press it down. Turn the Tire approximately 60 degrees and repeat.

3/   Depending on the width of the Tire you may need to repeat the process on the inside also.


How to True Sponge Tires.

   Truing Sponge Tires is essential if you are serious about racing competitively. To do this you will need the piece of wood, as described earlier and a good pair of vernier or digital calipers.
   Sponge Tires will always wear unevenly, weather you race on Carpet or Tarmac. The outside wheels will always end a race smaller than the ones on the inside, so after each race I recommend swapping them over (unless you are fortunate to have a new set for each race) and dont forget to adjust the steering trim on your transmitter before the next race.

1/   Before starting, check each mounted Tire for diameter and order them smallest to largest. Start with the smallest and mount it in the lathe.

2/   Make sure you are wearing safety glasses before you start this procedure: Lay the sanding wood under the Tire so that it can be pivoted up from behind onto the Tire. Start the lathe spinning, so that as you stand infront of the Tire, it is rotating downwards. Slowly lift the sanding wood and try to hold it ridged as it comes up against the Tire. There will be a high point on the Tire that if you hold the bat rigid enough will eventually wear down until the Tire appears completely concentric. at this point stop the lathe and measure the diameter on the inside and outside of the width. If needs be, repeat the process until satisfied.
Repeat for each Tire, matching them in pairs for diameter.
If considered necessary also trim the sides.


For More Setup Information check out my Hints and Tips page.







Hints and Tips

Tires for RC Models

Rubber Tires:

   Rubber Tires ALWAYS should have either soft sponge or rubber inserts. They will not function as they should without them. And if you are totally serious about your racing they should be glued to the rims.

   You should also have at least three different compounds (Soft, Medium and Hard) fo varying track temperatures in On Road tarmac racing Touring cars, and varying pin sizes for carpet, and Off Road racing Buggys and Trucks.


How to Mount Rubber Tires onto Wheels/Rims.

   Before mounting your Tires, I would recommend talking to the more experienced racers at your local club, as to what inserts they use. Even the top level racers rely on a bit of local knowledge on tracks they have never raced before.

1/   Once you have decided what inserts to use, position them inside the Tires ready to go onto the rims.

2/   You will need strong fingers to pull and maneuver the Tires over the rims, so you may need the help of an adult. I would recommend NOT using metal Tire levers or a spoon as they can not only damage the fragile plastic rims but can also put small tears in the rubber, that could cause problems later.
   The technique I recommend, is to first of all hook the Tire on one side of the rim, then using the thumb and forefinger, grip the Tire and pull it upwards and over into position around the middle of the wheel, then over to its final position on the far side so that the beading is seated in the spigot. then position the near side beading in the opposite spigot making sure the sponge (or rubber) insert is not trapped and positioned centrally.

3/   You have the option of either gluing or not gluing your tires in position. If the track you race at is not too grippy you can get away with it, but on high grip tracks there is the possibility the tire might pull away from the rim and ruin your race.
My recommendation is to glue them.
   Superglue is the thing to use. To do this, carefully pull the beading out of its seating, put on a spot of glue, then quickly push it back down. repeat this at least 6 times around each side of the wheel.
Superglue can be dangerous, so this is best done by an adult.

For More Setup Information check out my Hints and Tips page.










On/Off Road
RC Models:

Radio
Equipment:

Accessories: