From Around The WORLD
|
| |||||
|
From Around The WORLD
|
RC Model Bateries For Sale: Voltage: 7.2 Volt Batteries 7.4 Volt Batteries 8.4 Volt Batteries 9.6 Volt Batteries 11.1 Volt Batteries Capacity: 900mah Batteries 1200mah Batteries 1400mah Batteries 1500mah Batteries 1800mah Batteries 2000mah Batteries 2200mah Batteries 2800mah Batteries 3000mah Batteries 3800mah Batteries 4000mah Batteries 4200mah Batteries 4500mah Batteries 5000mah Batteries 6000mah Batteries Model: Airplane Batteries Boat Batteries Buggy Batteries Helicopter Batteries Touring Car Batteries Truck Batteries Truggy Batteries Accessories: Battery Chargers Battery Dischargers Battery Connectors Battery Heatsinks Battery Jigs Voltage Indicators Radio Batteries: Receiver Batteries Transmitter Batteries |
|
RC Model Bateries For Sale: Manufacturers: Associated Batteries Coyote Batteries Duratrax Batteries Dynamite Batteries EC Power Batteries Esky Batteries Firefox Batteries Hobbymix Batteries Hobbyzone Batteries HPI Batteries Losi Batteries LRP Batteries Mardave Batteries Maxamps Batteries Maxforce Batteries Nikko Batteries RC Lab Batteries RCS Batteries Ripmax Batteries Sanyo Batteries SMC Batteries Speed Passion Batteries Spektrum Batteries Tamiya Batteries Team Orion Batteries Tenergy Batteries Traxxas Batteries Trinity Batteries Turnigy Batteries Ultrafire Batteries Venom Batteries Type: AA Batteries AAA Batteries Li-Po Batteries Ni-Cad Batteries Ni-Mh Batteries Pack Type: Hump Pack Batteries Saddle Pack Batteries Stick Pack Batteries |
|
|
|
|
It Might be here Tomorrow. |
|
|
Custom Search
|
|
Battery Charging Ni-Cad (Nickel Cadmium) 1/ All Ni-Cad Batteries have to be Discharged soon after use. This is to avoid the dreaded "Memory" effect that on subsequent re-charges can cause a momentary drop in performance during a race. A simple discharger can be made from a car 12v bulb. 2/ Try to time your charge to complete just before a race. This will ensure maximum punch and duration. If a Ni-Cad is left to cool after a charge this advantage dissipates. 3/ The higher the charge current the more Punch the Ni-Cad battery will have (up to around 8 amps), however, the downside to this is a reduction in duration and effective battery life. 4/ Ni-Cad Batteries should be left to cool for about an hour after use before recharging. This will increase the effective life of the battery. 1/ Never charge Ni-Mh batteries at a current higher than 4.5 amps. Although these batteries can give a higher voltage than Ni-Cad Batteries, they are much more sensitive and easy to damage if charged too quickly. 2/ Charging methods Ni-Mh batteries can also be detrimental. The best I found was the "Slope" method. Avoid "Pulse" charging as this tends to effect crystal formation detrimentally and (it seems to kill them off) thus reduces duration over time. 3/ If using a temperature cut off charger on Ni-Mh batteries set to no more than 40 Degrees Centigrade. Any higher than this can damage the crystals. 4/ It is not necessary to discharge Ni-Mh Batteries. Unlike Ni-Cad batteries they do not develop a memory. Also, if they are totally discharged they sometimes will not charge straight after and need to be coaxed with a 10 minute trickle charge. 5/ Ni Mh Batteries can be recharged shortly after use without any discernable detrimental effects. |
|
Radio Gear How to avoid Interference. 1/ The first consideration when installing your Receiver into your Electrically Powered Model is to make sure it is well away from the Negative Battery terminal, and the Motor. The Magnetic field can cause stuttering type interference at times of high current draw (i.e., Fast Acceleration) 2/ Make sure the Ariel tube is long enough for the Ariel wire. The tip of this wire is highly sensitive and should be as high, and as far away from the Motor as possible (yup, its that magnetic field prob again) 3/ If all else fails, a simple tip that often works for all RC Model enthusiasts is to wrap the receiver in Aluminium Foil, to shield against any magnetic and external radio interference. 4/ As a last resort, to protect against servo twitch, try ferrite beads. (available at Radio Shack or Maplins) These are threaded over the red, white (or yellow) and black wires of each servo. |
|
|
|
|
|
 |
| |||||
Every effort is made to ensure that information contained within the RCScrapyard site is correct and fair. However, no responsibility can be taken for errors, omissions or inaccuracies. Any complaints will be dealt with as soon as possible. © RCScrapyard |
For Sale in the UK