Radio Controlled Models
Share RCScrapyard on Facebook
RCScrapyard Radio Controlled Models
Flags
RCScrapyard.net contains Google AdSense Ads and Amazon Affiliate links, from which we may earn commission. See our Disclosure page for more information.
bar

Tamiya Ferrari F40 - 58356 (Radio Controlled Model Review)

1/10 Scale Electric Touring Car - Group-C Chassis:

  Released by Tamiya on September 14, 2005, the Ferrari F40 is a "Finished Body" version of the car driven by Jean Alesi in the IMSA GT one hour race in 1989, finishing third. This model had originally been released by Tamiya in September 1991 (#58098).

Tamiya Ferrari-F40 - #58356

▼ Scroll Down for More Images ▼



  The chassis for this car was a short wheelbase version of the one used for the Mercedes Benz C11 (#58088) designated the "Group-C" chassis.

  The configuration of the "Group-C" chassis was similar in a number of ways to the F101, not least in that it employed a ball differential in place of the older Orbital Gear type. This, combined with its low centre of gravity, gave the car improved stability when cornering and smoother, controlled acceleration out of the corner.

  The success of the pan car style design of the "Group-C" chassis was mainly down its relatively simple construction, low price and handling abilities. This was the twelfth RC model, made by Tamiya, to use the "Group-C" chassis, so parts and spares should not be too difficult to find.


Rating: 44 Stars out of 5 RCScrapyard



Gas/Nitro Engines Body Shells Radio Transmitters etc Tires Wheels/Rims Electronic Speed Controllers Battery Packs / Chargers Electric Motors




















Flags

Tamiya Ferrari F40 #58356 Group-C - Chassis
Tamiya Ferrari F40 #58356 Group-C Chassis
Tamiya Ferrari F40 #58356 Group-C
Tamiya Ferrari F40 #58356 Group-C Body Shell

Buying a Used Tamiya Ferrari F40
Touring Car (and What to look for)


   There are essentially three reasons you might want to buy a used Tamiya Ferrari F40 Electric Touring Car; you may be a collector, looking to restore and display it; restore and sell for a profit; or simply restore and race an iconic vintage model. Personally, I used to get a buzz out of restoring an old clapped-out model, installing modern day electrics and maybe a few hop-ups, then showing the gang at our local club, just how competitive those old models could still be.

   Cheap, pre-loved bargain models, parts and spares are always coming up for sale, but once you have made your purchase, the one thing you will always need, is an instruction manual. If not supplied with your purchase, they can often be downloaded from the Tamiya website, or purchased separately on eBay. With an instruction manual, any problems with your model Touring Car you may discover, can easily be fixed.

Make a General Visual Inspection

Dampers
   When you receive your used Tamiya Touring Car, make a general visual inspection of the chassis, front and rear wishbones, suspension shock towers etc, for any broken parts that may need to be replaced. Then, take a screwdriver and box spanner and check each self tapping screw and nut for security, taking care not to over tighten.

   Next, for those Tamiya models with oil filled shock absorbers, remove them from the chassis and dismantle the coil springs. The damper shafts should push in and pull out with a smooth action. If you feel a jolt as you change direction, this means the oil has leaked out and must be topped up. At the same time, change the O-Ring seals to prevent more leakage. Also check the damper shafts for damage. If they are scratched, change them as soon as possible.

Check the Body-Shell

   If the body shell of your Tamiya Ferrari F40 is broken, ripped or damaged in any way, this can be easily repaired with rubber solution glue. Also, for added protection and if available for your Ferrari F40 model, fit an under guard to stop dirt and gravel entering the chassis.

Drive Shafts and Turnbuckles

Titanium Turnbuckles
   Examine the drive shafts for wear and replace as required. If possible, change them for titanium. The steel shafts wear and bend too easily.

   If you intend to race your Ferrari F40 Touring Car model at a competitive level, I would also recommend you obtain and fit titanium pivot shafts, turnbuckles, tie rods and steering rods.

Examine the Drive System

   On Belt driven models, the Drive Belts need checking at regular intervals for wear, tension and damage. If deemed necessary, adjust the tensioning pulley until the belt can be depressed in the centre by no more than around 5mm. If the belt was slack, also examine the drive pulleys for wear. The teeth should provide a well seated fit for the belt teeth and not be rounded on the corners. If the belt teeth do not fit snugly, change the pulleys as soon as possible. For top level racing it may be prudent to replace all belts and pulleys after each race meeting.

   For Gear driven models, the gearbox of your used Touring Car should be opened up to check for gear wear and lubrication. A thin coat of grease is often used on internal gears and although this is fine for basic running around on the back yard, if you intend to race your Touring Car at a higher level, this should be removed and replaced with racing oil (ZX1 or Teflon Oil). Of course, this should be reapplied after each race meeting.

Pinions and Spur Gears

Spur Gears
   Gears are a weakness on all Touring Car RC models. Head on collisions can easily damage the gear teeth on nylon and plastic spur gears. Heavy impacts can also loosen the nuts or self tapping screws that hold the Electric Motor in Position, allowing the pinion gear to pull out of mesh slightly and rip the tops off the teeth on your spur gear. To minimise this possibility, fit bolts with locking nuts to the Electric Motor mount and remember to check them for security after every two or three runs.

Don't Neglect the Ball-Joints

   Ball joints always cause problems. For top level Electric Touring Car racing, the plastic ball connectors should be checked and if deemed necessary, changed after every meeting. A simple thing like a loose fitting connector popping off, could easily end your race, so better safe than sorry.

Steering Servo and Servo-Saver

Servo Gears
   The Ferrari F40 steering servo is also prone to damage. In high speed crash situations, the fragile gear teeth of the servo can be broken off, rendering your expensive servo useless, so be sure to obtain a good quality "Servo Saver". Check out my Servo Information article.

Stabilizers

   If body roll on your Tamiya Ferrari F40 is a problem, handling can be improved with the use of stabilizers, anti roll or sway bars, stiffer tuning springs and, or, thicker silicone oil in the dampers.

Don't Forget those Bearings

Ball Bearings
   If your used Tamiya Touring Car comes with plastic and sintered brass bushings (ring type bearings), check the shafts that run in them for wear. Dust and grit can get into these bearings and abrade the shafts. Therefore, you should replace them all with shielded ball bearings. If the model has been run with ring type bearings, you may have to change all the axles and driveshafts. For more information, take a look at my article, How to get the best from your Bearings.

   Finally, good luck with your Ferrari F40 model and good racing.

▼ Scroll Down for More Articles and Advice ▼

Or, check out our RC Model Car Setup Guide



















Tamiya Buggys Tamiya Trucks Tamiya Monster Trucks Tamiya Rock Crawlers Tamiya Off Road Chassis Types Tamiya Touring Car Tamiya Drift Car Tamiya WRC Car Tamiya M Chassis
Tamiya Tractor Trucks Tamiya Touring Car Chassis Tamiya F1 Tamiya F1/Le Mans Chassis Types Tamiya Military Tamiya Tanks


















Hints, Tips and Information

How to Reduce the Weight of your RC Model Car

   If you ever step up and enter a regional, national or international event in RC, you will find one specific rule concerning the weight of your car.

   At the time this article was written, the Minimum weight restrictions for 1:10 electric Touring Cars at different events, was between 1350g and 1500g. This includes your Motor, ESC, Receiver, Battery, Body Shell and the transponder.

   Out of the box you will find the majority of 1:10 Touring Cars, with everything onboard, are way over this Minimum weight, and unless you are good enough to attract sponsors, getting your car down to anything approaching that minimum weight will be very expensive.

   There are things you can buy like micro ESC, and Receivers. But Batteries and Motors are what they are, and you have to work around them.

   To reduce the weight of your chassis, there are a number of things you can do.

Read the Complete Article  ▶ ▶






Hints, Tips and Information

Ball Differentials

   Ball differentials were developed in the late 1980s to replace the high friction Gear differentials. Mainly used on Touring Cars, Pan Cars and Formula One Cars, Ball Differentials are designed to be totally frictionless and smooth in action to provide effortless drive to the wheels on cornering, where the inside wheels must rotate slower than the outside wheels for controlled stability.

   Basically, the configuration of the Ball Differential is a number of small case hardened steel balls, spaced in a plastic cage that is in effect the drive gear for the axle. On each side of the gear are two hardened and tempered pressure plates that clamp over the steel balls, held in position by a screw through the centre of the assembly, incorporating a small thrust bearing and coil spring. The adjustment of this screw is crucial to the effectiveness of the differential action.

Read the Complete Article  ▶ ▶







^ TOP ^

RC Models:
Radio
& Motors:
Other
Accessories: